Himalayan Pink Salt Tiles 8" x 4" x 1" - Pack of 30

Himalayan Pink Salt Tiles 8" x 4" x 1" (Pack of 30)

This pack of 30 Himalayan pink salt tiles covers 6.67 square feet and weighs about 75 pounds total, enough to build one large feature wall or face a full small bathroom. Each tile is 8" x 4" x 1", batch-matched, and cut from the Khewra Salt Mine in Punjab, Pakistan. In a 6x5 grid, thirty tiles form a 48-inch-wide by 20-inch-tall panel, and the pack still ships by standard carrier rather than freight.

Thirty tiles is the "one big wall done right" size. It sits between the 20-pack accent wall and the 50-pack room build, so the numbers below help you confirm it's the right scope before ordering.

How much wall does a pack of 30 cover?

Thirty tiles cover 960 square inches, or 6.67 square feet, with each tile covering 32 square inches. The most balanced layout is a 6x5 grid at 48" wide by 20" tall. You can also run a 10x3 horizontal band at 80" wide by 12" tall, or wrap a small room across three walls. Here is the coverage at a glance.

From our workshop: the 30-pack is the biggest wall we still recommend a confident non-professional tackle solo. Past this size, the weight and the level-line management usually call for a second set of hands. At 30 tiles on studs, one careful person over a weekend gets a clean result.

How much adhesive and lighting do you need?

For 30 tiles, plan on 5 to 6 tubes of pink salt adhesive, since one tube bonds about 5 to 6 tiles. For even backlighting behind a 48" x 20" grid, plan 120 to 160 inches of warm-white LED strip at 2700K to 3000K, run off one transformer. Warm white brings out the pink and coral. Cool white flattens it to gray.

• Adhesive: 5 to 6 tubes of salt-bonding adhesive for a 30-tile wall.
• Lighting: 120 to 160 inches of LED strip, 2700K to 3000K, dimmable.
• Tools: 4-foot level, stud finder, tape measure, putty knife, tile spacers.

How do you install a 30-tile salt wall?

Budget six to eight hours plus cure time, ideally across a weekend. Confirm the studs behind a 75-pound wall, set a dead-level bottom row, then build upward in courses so lower tiles carry the ones above. Work in sets of about six to keep the line true, and cure the finished wall 48 to 72 hours before switching on any lights.

1. Find the studs, tape out the full 48" x 20" grid, and level the outline.
2. Mount and test the LED strip 1 to 2 inches behind the tile plane.
3. Set a perfectly level bottom row as the foundation for every course.
4. Spread thin, even adhesive on each tile and press 30 seconds.
5. Build upward in courses of six, checking level constantly.
6. Wipe squeeze-out immediately, then cure 48 to 72 hours before lighting.

Should I buy the Pack of 30, or the 20 or 50?

Choose the 30-pack for one large 6.67 sq ft wall or a full small bathroom that the 20-pack can't quite cover. Step down to the 20-pack for a standard accent wall, or up to the 50-pack for a room-scale job. The 30 still ships by standard carrier, while the 50 ships palletized by freight. Here is how they compare.

Common mistakes on a large single wall

At 30 tiles, the errors that cause a redo are an unlevel base row, exact-count ordering with no spares, and lighting before the wall cures. Get the first row dead level and the rest of the grid follows it.

• Level the bottom row first. Every course above inherits its angle.
• Order a few spare tiles. Natural salt chips at the edges in handling.
• Wait the full cure time. Heat from lights too early can loosen tiles.

Pack specifications

Care and quality

Dust the wall with a dry microfiber cloth about once a week and skip liquid cleaners, since water dissolves salt. Keep the panel out of direct shower spray, and expect a little surface dampness in humid weather, which wipes off dry. Every tile is inspected for cracks and color-matched to the batch, then individually wrapped so a 75-pound order arrives intact.

A pack of 30 Himalayan salt tiles covers 6.67 square feet and builds a 48-inch by 20-inch feature wall, using five to six tubes of salt adhesive and 120 to 160 inches of warm-white LED strip.

Key takeaways

• Thirty batch-matched tiles, about 2.5 lb each and 75 lb total, from Khewra rock salt.
• Covers 6.67 square feet, a 48" x 20" grid in the standard 6x5 layout.
• Right size for one large wall or a full small bathroom.
• Plan 5 to 6 tubes of adhesive and 120 to 160 inches of warm-white LED strip.
• Still ships by standard carrier, unlike the freight-only 50-pack.