Himalayan Pink Salt Tiles 8" x 4" x 1" - Pack of 10

Himalayan Pink Salt Tiles 8" x 4" x 1" (Pack of 10)

This pack of 10 Himalayan pink salt tiles covers 2.22 square feet and weighs about 25 pounds total, enough to build a real feature wall or full backsplash rather than an accent. Each tile is 8" x 4" x 1", batch-matched, and cut from the Khewra Salt Mine in Punjab, Pakistan. In a 5x2 grid, ten tiles form a 40-inch-wide by 8-inch-tall panel.

Ten tiles is the point where planning matters: coverage, adhesive, and lighting all scale up. Below is the exact math so you order the right amount of each and avoid a half-finished wall.

How much wall does a pack of 10 cover?

Ten tiles cover 320 square inches, or 2.22 square feet, with each tile covering 32 square inches. The most common layout is a 5x2 grid at 40" wide by 8" tall. You can also run a 2x5 vertical column at 16" wide by 20" tall, or an L-shape that wraps a corner. Here is the coverage at a glance.

From our workshop: order two or three extra tiles beyond your exact grid, not the precise count. Natural salt chips at the edges during handling, and on a 10-tile wall a single cracked corner ruins the line. The Pack of 10 already builds a clean 5x2 with none left over, so if your design is tight, size up to the next pack for spares.

How much adhesive and lighting do you need?

For 10 tiles, plan on 2 tubes of pink salt adhesive, since one tube bonds about 5 to 6 tiles. For even backlighting behind a 40" x 8" grid, plan 60 to 100 inches of warm-white LED strip at 2700K to 3000K, run off one transformer. Cool-white light makes salt look gray, so stay warm and use a dimmer if you can.

• Adhesive: 2 tubes of salt-bonding adhesive for a 10-tile grid.
• Lighting: 60 to 100 inches of LED strip, 2700K to 3000K, dimmable.
• Tools: 4-foot level, tape measure, putty knife, painter's tape, tile spacers.

How do you install a 10-tile salt wall?

Plan on a two-day job: mock up and light on day one, bond and cure on day two. Confirm the wall can carry 25 pounds across 2 square feet (standard drywall on 16-inch studs is usually fine), set a level bottom row, then build upward in sections so lower tiles support the ones above. Cure for 48 hours before switching on lights.

1. Tape out the full 40" x 8" outline on the wall and check it with a level.
2. Mount and test the LED strip 1-2 inches behind the tile plane.
3. Spread a thin, even layer of pink salt adhesive on the back of each tile.
4. Start at the bottom-left, press each tile for 30 seconds, and check the level before the next.
5. Work in two sets of 5 with a short rest between to keep the line accurate.
6. Wipe squeeze-out right away, then cure 48 hours before lighting or cleaning.

Common mistakes on a 10-tile wall

Bigger walls punish small errors. The three that cost people a redo: an unlevel bottom row, too much adhesive, and lighting the wall before it cures. Get the first row perfectly level and the rest follows.

• Level the bottom row first. Every tile above inherits its angle.
• Use thin adhesive. Thick globs squeeze out and shift tiles off line.
• Wait the full 48 hours. Heat from lights before curing can loosen tiles.

Pack specifications

Per-tile pricing across packs

Larger packs lower the per-tile cost. If you're deciding how much wall to build, here is where the Pack of 10 sits.

Care and quality

Dust the wall with a dry microfiber cloth about once a week, which takes a couple of minutes across ten tiles. Skip liquid cleaners, since water damages salt, and keep the panel out of direct shower spray. In humid weather, the surface may feel slightly damp on its own, which is normal. Every tile is inspected for cracks and color-matched to the batch before it ships.

A pack of 10 Himalayan salt tiles covers 2.22 square feet and builds a 40-inch by 8-inch feature wall, using two tubes of salt adhesive and about 60 to 100 inches of warm-white LED strip.

Key takeaways

• Ten batch-matched tiles, about 2.5 lb each and 25 lb total, from Khewra rock salt.
• Covers 2.22 square feet, a 40" x 8" grid in the standard 5x2 layout.
• Plan 2 tubes of salt adhesive and 60 to 100 inches of warm-white LED strip.
• Level the bottom row, build in two sets of 5, and cure 48 hours before lighting.
• Order a few spares if your design is tight, since edges can chip in handling.